ESP32-S3 1.9" Display Dev Board with IMU

This compact ESP32-S3 development board includes a 6-axis IMU and 1.9" LCD display - with a variant option including touch control - and has a pinout compatible with the Raspberry Pi Pico, allowing the use of Pico HATs and other Pico-intended hardware! The popular ESP32-S3 provides 2.4GHz Wi-Fi along with Bluetooth 5 LE via an onboard ceramic antenna, and comes with the usual built-in 512KB SRAM and 384KB ROM, supported by the onboard 16MB FLASH and 8MB PSRAM. The board is powered and programmed by USB-C. The display is a small 1.9" panel with a 170x320 resolution, 160° viewing angles and 262k colours. A version with touch control is available, select the appropriate variant before adding to cart. Other features include a QMI8658 6-axis IMU (3-axis accelerometer and 3-axis gyroscope) for detecting motion gestures, a microSD slot, connector for a MX1.25/PicoBlade-compatible lithium battery (with charging circuit) and the BOOT/RESET buttons. In fact, the non-touch and touch versions have a couple of other differences too:

* The non-touch version includes a WS2812 RGB LED on the underside * The touch version includes an IPEX1 connector for using an external antenna (resistor resoldering required to enable) * The touch version includes touch input (but you knew that already!)

What's Onboard? * ESP32-S3R8

* Dual-core processor with an operating frequency of up to 240 MHz

* W25Q128 16 MB Flash * MX1.25 battery header

* MX1.25 2-pin connector for a 3.7 V lithium battery, supports charging and discharging

* RESET button * USB-C port

* Used for power input and data transmission

* TF card slot (on the rear)

* Supports TF cards for external storage

* Charge indicator

* Battery charge LED: on while charging, off when fully charged

* BOOT button

* Used for firmware download or entering boot mode

* WS2812 RGB LED (non-touch version only)

* Coloured lighting LED located on the underside of the PCB

* QMI8658 sensor (on the rear)

* 6-axis IMU with a 3-axis gyroscope and a 3-axis accelerometer

* IPEX1 connector (touch version only)

* Supports use of an external antenna via resistor re-soldering

* Onboard ceramic antenna

* Space-saving antenna design for stable wireless performance

Features

* ESP32-S3 development board with dual-core Xtensa LX7 processor up to 240 MHz * 2.4 GHz Wi-Fi (802.11 b/g/n) and Bluetooth 5 LE via onboard ceramic antenna * 16 MB Flash and 8 MB PSRAM, plus built-in 512 KB SRAM and 384 KB ROM * 1.9" LCD display, 170 × 320 resolution, 262K colours, 160° viewing angles * Touch-enabled variant available (select version before purchase)

* QMI8658 6-axis IMU (3-axis accelerometer and 3-axis gyroscope) * Raspberry Pi Pico–compatible pinout for use with Pico HATs and accessories * USB-C for power, programming, and debugging * MicroSD card slot for external storage * MX1.25 / PicoBlade-compatible LiPo battery connector with charging circuit * BOOT and RESET buttons * Non-touch version includes an onboard WS2812 RGB LED * Touch version adds capacitive touch input and an IPEX1 connector for an external antenna (resoldering required) Specifications Display panel LCD Display size 1.9" Resolution 170 × 320 Display colours 262K Brightness 500 cd/m² Contrast ratio 900:1 Communication interface SPI Driver IC ST7789V2 Touch Supported (touch version only) Touch IC CST816 (touch version only) Resources

* Product Wiki * Schematic

* Non-touch * Touch

* Dimensions

* Non-touch * Touch

* ESP32-S3 Series Datasheet * ST7789 Datasheet * QMI8658 Datasheet * CST816 Datasheet Pinout Package Contents

* 1x ESP32-S3 1.9" Display Dev Board (170x320)

* Select non-touch or touch when adding to cart