Sparkfun Pixhawk 6C with PM02 Power Module

The Pixhawk® 6C is a cutting-edge addition to the renowned Pixhawk® series of flight controllers. Built on the Pixhawk® FMUv6C Open Standard and Connector Standard, it comes with pre-installed PX4 Autopilot®. It is powered by an STMicroelectronics® based STM32H743 and incorporates sensor technology from Bosch® & InvenSense®. The Pixhawk® 6C is ideal for controlling any autonomous vehicle and is suitable for both academic and commercial applications.The Pixhawk® 6C's H7 microcontroller, which contains the Arm® Cortex®-M7 core, operates at a speed of up to 480 MHz. It is equipped with 2MB flash memory and 1MB RAM. The increased processing power enhances developer productivity and efficiency, facilitating the execution of complex algorithms and models. The FMUv6C open standard features high-performance, low-noise IMUs, offering cost-effective IMU redundancy. The controller also has a vibration isolation system to filter high-frequency vibrations and reduce noise, ensuring accurate readings and improved overall flight performance.The Pixhawk® 6C is an excellent resource for corporate research labs, startups, academic institutions, and commercial applications. It enables the development of advanced autonomous vehicles and drones, providing a versatile platform for innovation and experimentation.The PM02 Power Module is an efficient way to provide your autopilot flight controller with clean power from a LiPo battery. It offers current consumption and battery voltage measurements through a 6-pos cable. The module's on-board switching regulator outputs 5.2V and a maximum of 3A from up to a 12S LiPo battery. The fully-assembled module comes with XT60 connectors and is wrapped in shrink tubing for protection. It is designed to power the autopilot flight controller, a RC receiver and APM accessories. The GH terminal is also compatible with Pix32, Pixhawk4, Pixhawk4 mini, Pix32v5 and Durandal.Package Contains:

* 1x Pixhawk 6C Flight Controller Module * 1x PM02 V3 12S Power Module * 1x Cable Set Key Features:Processors & Sensors

* FMU Processor: STM32H743

* 32 Bit Arm® Cortex®-M7, 480MHz, 2MB memory, 1MB SRAM

* IO Processor: STM32F103

* 32 Bit Arm® Cortex®-M3, 72MHz, 64KB SRAM

* On-board sensors

* Accel/Gyro: ICM-42688-P * Accel/Gyro: BMI055 * Mag: IST8310 * Barometer: MS5611

Electrical Specifications

* Voltage Ratings:

* Max input voltage: 6V * USB Power Input: 4.75~5.25V * Servo Rail Input: 0~36V

* Current Ratings:

* Telem1 Max output current limiter: 1.5A * All other port combined output current limiter: 1.5A

Interfaces

* 16- PWM servo outputs (8 from IO, 8 from FMU) * 3 general purpose serial ports

* Telem1 - Full flow control, separate 1.5A current limit * Telem2 - Full flow control * Telem3

* 2 GPS ports

* GPS1 - Full GPS port (GPS plus safety switch) * GPS2 - Basic GPS port

* 1 I2C port

* Supports dedicated I2C calibration EEPROM located on sensor module

* 2 CAN Buses

* CAN Bus has individual silent controls or ESC RX-MUX control

* 2 Debug port

* FMU Debug * I/O Debug

* Dedicated R/C input for Spektrum / DSM and S.BUS, CPPM, analog / PWM RSSI * Dedicated S.BUS output * 2 Power input ports (Analog) Documentation:

* Pixhawk 6C Pinout * ArduPilot - Copter * ArduPilot - Plane * QGroundControl