PIC18F46K80-I/PT 8-bit PICmicro microcontroller, 64 KB, 64 MHz, TQFP-44

PIC18F46K80 FAMILY - 28/40/44/64-Pin, Enhanced Flash Microcontrollers with ECAN™ XLP Technology

Special Microcontroller Features: - Operating Voltage Range: 1.8V to 5.5V - On-Chip 3.3V Regulator - Operating Speed up to 64 MHz - Up to 64 Kbytes On-Chip Flash Program Memory: - 10,000 erase/write cycle, typical - 20 years minimum retention, typical - 1,024 Bytes of Data EEPROM: - 100,000 Erase/write cycle data EEPROM memory, typical - 3.6 Kbytes of General Purpose Registers (SRAM) - Three Internal Oscillators: LF-INTOSC (31 KHz), MF-INTOSC (500 kHz) and HF-INTOSC (16 MHz) - Self-Programmable under Software Control - Priority Levels for Interrupts - 8 x 8 Single-Cycle Hardware Multiplier - Extended Watchdog Timer (WDT): - Programmable period from 4 ms to 4,194s - In-Circuit Serial Programming™ (ICSP™) via Two Pins - In-Circuit Debug via Two Pins - Programmable BOR - Programmable LVD

Power Management Features: - Run: CPU on, Peripherals on - Idle: CPU off, Peripherals on - Sleep: CPU off, Peripherals off - Two-Speed Oscillator Start-up - Fail-Safe Clock Monitor (FSCM) - Power-Saving Peripheral Module Disable (PMD) - Ultra Low-Power Wake-up - Fast Wake-up, 1 µs, Typical - Low-Power WDT, 300 nA, Typical - Run mode Currents Down to Very Low 3.8 µA, Typical - Idle mode Currents Down to Very Low 880 nA, Typical - Sleep mode Current Down to Very Low 13 nA, Typical

ECAN Bus Module Features: - Conforms to CAN 2.0B Active Specification - Three Operating modes: - Legacy mode (full backward compatibility with existing PIC18CXX8/FXX8 CAN modules) - Enhanced mode - FIFO mode or programmable TX/RX buffers - Message Bit Rates up to 1 Mbps - DeviceNet™ Data Byte Filter Support - Six Programmable Receive/Transmit Buffers - Three Dedicated Transmit Buffers with Prioritization - Two Dedicated Receive Buffers ECAN Bus Module Features (Continued): - 16 Full, 29-Bit Acceptance Filters with Dynamic Association - Three Full, 29-Bit Acceptance Masks - Automatic Remote Frame Handling - Advanced Error Management Features

Peripheral Features: - Five CCP/ECCP modules: - Four Capture/Compare/PWM (CCP) modules - One Enhanced Capture/Compare/PWM (ECCP) module - Five 8/16-Bit Timer/Counter modules: - Timer0: 8/16-bit timer/counter with 8-bit programmable prescaler - Timer1, Timer3: 16-bit timer/counter - Timer2, Timer4: 8-bit timer/counter - Two Analog Comparators - Configurable Reference Clock Output - Charge Time Measurement Unit (CTMU): - Capacitance measurement - Time measurement with 1 ns typical resolution - Integrated voltage reference - High-Current Sink/Source 25 mA/25 mA (PORTB and PORTC) - Up to Four External Interrupts - One Master Synchronous Serial Port (MSSP) module: - 3/4-wire SPI (supports all four SPI modes) - I2C™ Master and Slave modes - Two Enhanced Addressable USART modules: - LIN/J2602 support - Auto-Baud Detect (ABD) - 12-Bit A/D Converter with up to 11 Channels: - Auto-acquisition and Sleep operation - Differential Input mode of operation - Data Signal Modulator module: - Select modulator and carrier sources from various module outputs - Integrated Voltage Reference